Home About us Products Produce&Inspect Contact us
SML
SML

Cast Iron Pipe conforming to DIN/EN877/ISO6594
Material:Cast Iron with flake graphite
Qualilty:GJL-150 according to EN1561
Coating: SML,KML,BML,TML
Size:DN40-DN300
The gray cast iron soil pipes produced by centrifugal technology which are used
in drainage sewer system and ventilation ducts system through a flexible linkage.
which have following advantages :flat straight,even pipe wall.
high strength and density,high smoothness internal and external surface,
no casting defect, easy installation, easy maintain, long using life,
environmental protecting,fireproofing and no noise.

  

DN

External diameter  DE(mm)

Wall thickness(mm)

Unit weight

Length

Nominal value

Tolerance

Nominal value

Minimum value

kg/pc

(mm)

40

48

¡¡+2

  -1

3.0 

2.5 

12.70 

3000+/-20

50

58

3.5 

3.0 

13.00 

70

78

3.5 

3.0 

17.70 

75/80

83

3.5 

3.0 

18.90 

100

110

3.5 

3.0 

25.20 

125

135

¡¡+2

  -2

4.0 

3.5 

35.40 

150

160

4.0 

3.5 

42.20 

200

210

¡¡+2.5

  -2.5

5.0 

4.0 

69.30 

250

274

5.5 

4.5 

99.80 

300

326

6.0 

5.0 

129.70 

 SML DIN/EN877 Cast Iron Socketless Pipes 

 

SML Above ground soil, vent and rainwater pipework

    1=  2 part epoxy
   
2= Cast Iron
    3= anti-corrosive primer 
 
Internal painting : two-part epoxy resin painting, ochre colour RAL 1021,
                          with an average dry thickness of 120 microns.
   External painting: anti-corrosive primer painting, red-brown colour RAL 2001, 
                            with average dry thickness 60 microns.

Epoxy Powder Coating DIN/EN877 Cast Iron Socketless Pipes

Coating:
Internal Coating : two-part epoxy resin powder coating, with an average dry thickness of 100-400 microns.
External Coating: two-part epoxy resin powder coating, with an average dry thickness of 100-400 microns.

The CE marking indicates a product¡¯s compliance with EU legislation and so enables the free movement of products within the European market. By affixing the CE marking to a product, a manufacturer declares, on his sole responsibility, that the product meets all the legal requirements for the CE marking, which means that the product can be sold throughout the European Economic Area (EEA, the 28 Member States of the EU and European Free Trade Association (EFTA) countries Iceland, Norway, Liechtenstein). This also applies to products made in other countries which are sold in the EEA.
However, not all products must bear the CE marking, only product categories mentioned in specific EU directives on the CE marking.
CE marking does not indicate that a product was made in the EEA, but merely states that the product has been assessed before being placed on the market and thus satisfies the applicable legislative requirements (e.g. a harmonised level of safety) enabling it to be sold there. It means that the manufacturer has:
• verified that the product complies with all relevant essential requirements (e.g. health and safety or environmental requirements) laid down in the applicable directive(s) and
• if stipulated in the directive(s), had it examined by an independent conformity assessment body.
It is the manufacturer¡¯s responsibility to carry out the conformity assessment, to set up the technical file, to issue the declaration of conformity and to affix the CE marking to a product. Distributors must check that the product bears the CE marking and that the requisite supporting documentation is in order. If the product is being imported from outside the EEA, the importer has to verify that the manufacturer has undertaken the necessary steps and that the documentation is available upon request
All pipes are produced according to standard DIN19522/EN 877/ISO6594 and not inflammable and not combustible.

Product List
DIN/EN877 Pipes
DIN/EN877 Fittings
ASTM A888/CISPI301/CSA B70 NH Pipe
ASTM A888/CISPI301/CSA B70 NH Fittings
ASTM A74 SV Pipe
BS 437/416 Pipes
Couplings and clamps
DI manhole covers and frame
ISO2531/EN545 DI pipes
Cast Iron Cookware
Grooved Coupling Fitting
Threaded Rods DIN 975
 
Contact us

Head office add: No.18 ,Fengshou Road,Shijiazhuang City Hebei province China-050047
Tel:  0086-311-67794622         
Fax: 0086-311-89912169
Skype ID:live:beisai_1
E-mail: Admin@bsi-metal.com
              
Beisai@126.com   
Web:www.bsi-metal.com

Welcome Beisai

Hebei BeiSai Metal Products Co.,Ltd  was located in ShiJiazhuang province City of China.
Our company is a professional supplier and manufacturer for metal hardware of high buildings.
Our main products and service is Casting Iron Pipes, Fittings, SS Couplings,
Carton Steel Clamps which was used for sewer drainage system of buildings.
And Casting iron manhole covers and frame , Casting tree gate and Casting cooking hardware ,
 Casting valves , Fire protection fittings and connectors, etc..

Product List
>   DIN/EN877 Pipes
>   DIN/EN877 Fittings
>   ASTM A888/CISPI301/CSA B70 NH Pipe
>   ASTM A888/CISPI301/CSA B70 NH Fittings
>   ASTM A74 SV Pipe
>   BS 437/416 Pipes
>   Couplings and clamps
>   DI manhole covers and frame
>   ISO2531/EN545 DI pipes
>   Cast Iron Cookware
>   Grooved Coupling Fitting
>   Threaded Rods DIN 975
Produce&Inspect
>   Physical & Chemical Analysis
>   Production and Technology
>   Testing & Inspection
Copyright © 2003-2013 www.bsi-metal.com , All Rights Reserved  ¼½ICP±¸°¸ºÅ£º036365ºÅ